doc harper

if your rubber portion of your hose is the only thing bad u can reuse the fittings. find someone who has an a/c hose crimper and buy some hose and crimp shells and it will look factory. if metal part is bad an a/c speciality shop can repair it. florida and Arizona have these.

looking to buy wave wave washers that go behind vent handle front and rear. 2 fronts and two rears. some may have two on each pivot.the back quarter vents are larger. call tommy 701-982-3221

I put the car on a lift and take out two body to frame nuts and jack the left side of body up about a inch and they come out easy. I used a under lift jack stand and let the car down just a little on the last one and that was real easy

jon out in ca. has those s/s mirror brackets that go in place of the short belt molding I'm looking for but I have two holes right above this part in the w/s pillar post and that is where I'm going to put my mirrors. if I would have known about the molding replacement thing with the mirror bracket that would have worked and I could have filled in the two holes on each side of the windshield pillar. I may go ahead and get the brackets and get holes filled in if I can't find the molding I need. thanks for your help

I wish I would have known the early models would have worked. I had a shop build one even with the x reinforcement and looks nice. thanks for your help. I still need the left side belt molding that goes in front of the left front door on the cowl.

I have a 1941 Packard 110 4 dr. sedan. I need info on how to attach front gravel shield panel that goes above the front bumper. I have the center brace attached to center section of the grille support. the gravel shield panel has two big holes I think for fog lights and under the gravel shield is two brackets on the each side. just wonder how to attach the sides of the panel to the bumper or if I'm missing something.

those on ebay are for 38-40 my car is a 41-42 the early ones want work.. thanks

john has the right side mud guard but no left. I found a sheet metal shop that says they can make one close to original. thanks

does anyone know if there was a gas/fuel door guard for a 1941 Packard 110 4 door sedan made? if so I'm looking for one to buy. call text tommy at 970-403-4935

if u come across the place in Washington let me know. thanks for your replay

the splash/mud guard is metal not rubber. it is behind the rear wheel and it bolts to the frame and to fender. flat metal with a x stamped in it for reinforcement. 1941 110 4 dr sedan

I need the drivers side rear mud/ splash guard, and also the short body welt moulding that goes on the drivers side cowling in front of the door and one tail light bezel that be used as a driver stuff doesn't have to be in new condition. something steel wool can clean up and as long as the bezel has the top tab. call tommy at 970-403-4935

looking for a rear view mirror for the inside. it has a stud on the back of the mirror that screws to the center windshield separator. if u have one let me know how much for mirror, condition and shipping to Colorado and zip is 81328

1941 Packard 110 . anyone have any ideas on how to make the park light lens retainer fit. I have after market plastic lens and when the retainer is screwed down the front of the retainer want stay in the hole in the front of the park light assembly so it swings out side to side, there is a pin sticking out of the retainer and want stay in the parking lamp hole when lens retainer is tighten .. is there anyway to adjust the retainer bar and bend it without breaking it. 970-403-4935 call or text. thanks tommy

looking to buy a park light lens retainer molding for a 1941 Packard 110. it's the narrow molding that goes on top of the lens and has a screw hole in the rear that screw to the park light assembly. could use gaskets to. call tommy or text at 970-403-4935.

I'm looking to buy a gas filler lid that goes on the left rear fender. I need all the hardware such as hinges, and bolts plus springs or what ever you have to complete this. 110 and 120 are the same. 1941-42. call tommy harper at 970-403-4935 thanks

trying figure out where the front seat return spring goes. anyone with any idea or a picture. it's was laying under the seat when I took it out to have it recovered. also a bracket was laying there and I can't figure out where they went on the seat track.

1941 Packard 110 4 dr. sedan. I need the chrome joints that connect the exterior glass mouldings together. I need them for both quarter glass mouldings and all 4 doors. these are the trim mouldings that go around the outside portion of quarter and door glass. call tommy at 970-403-4935

10-4

i guess your right if mine didn't come with them. 110 special i'm guessing. front and rear must be the same. i have one long one for the rear i'll measure it and see if its the same is the long one you have. thanks.

my 41 110 didn't come with front fender spears. do you know how many went on each fender?

i have a radiator, steering box/column with fair to good steering wheel. no horn button. might can find button. would trade or sell. need exterior sunvisor or chrome fender spears for front fenders. 1941 packard 110 4 dr. sedan. call tommy at 970-403-4935 docharper819@yahoo.com

i have a 41 packard 110 4 dr. sedan. it has 2 small holes on both windshield pillars up top and 2 small ones at the bottom. i don't know if the lower holes were for outside rear view mirrors or part of the sunvisor. i'm guessing the top holes are for the sunvisor. the lower holes are small like the top holes. could this be a factory sun visor and factory mirrors. i could send some pictures if anyone has any ideas

. if you don't want to sell the clock thats ok. i made a delete plate but i will buy the glove box latch and retainer that goes in the dash. give me a price and shipping and i can pay pal or either way you want your money. you can call me at 970-403-4935. thanks again

looking for a push button glove box lock for a 1941 packard 110. can be one with or with out key. non-locking is fine. i need what ever holds it in place to. all i have is the empty hole. thanks doc harper. 970-403-4935