john hanson

what I have for your 56 S 8.213 1324489 -9 Lower Gravel Shield Rear 8.213 1324486 Left or right. Upper Gravel Shield rear. NOS These fit ether 56 C or S and 76 C or S These will be hard to find I have others. But they fit other models. John Hanson

I have some 42 Buick molding witch molding do you nee and how long is it as some of it has lost it numbers. John Hanson

Ok I found one a 1336056 b 70 gm that 70 I don't believe means much. Now what size bearing do you need I have Standard - .001 -.002 or - .020 John Hanson

I mite have a new one .will check John Hanson

Try replacing the Vacuum hose to the carb. If it is blocked it will cause to shift at higher speed and hard. John Hanson

Did you ever get a clutch I still have this one and it is for the 320 engine. John Hanson

For those of you that are interested I have a lot Parts for the Dynaflow. Even large major parts. John Hanson

may have some push rods. I know I have some older ones They may not have the numbers on them so may need length They are NOS. I will check in a bit. John Hanson

Let me know what you want I do have some nos parts for 1939 Buick and some newer John Hanson

if I can find them I have 1 in a box .I'll check today JohnHanson

Did some checking I have Clutch release bearing 1319083 I have the larger pressure plate and both sizes clutch plates The numbers are gone on the box with the pressure plate the number should be 1315074 then if you wanted to I have most of the parts to rebuild it back to original like the waffle spring the face plate and other parts. Don't know of anybody that rebuilds them so I may have to gather them up and scrap them. Send an email and i'll send some pictures or a phone number John Hampshire IL. 847 340 0727

I no sooner posted to you and I think I am thinking of the wrong bolt. The one I am talking about clams the air cleaner to the carb. I"ll look around I may find one but I doubt it John

Sorry it toke so long What I have is one for 1954 to 1956 2 BBL and the other one is 9 1/2" long total and of that there is 1 1/2" of thd. 1/4 x20 Send an email and I"ll send some pictures John

I have some NOS Clutch and pressure plates I'll Check them out and see if I have what you want John hanson

I'll check in the morning I should have some John Hanson

I think I have a new one .might have to know the length of it. I have 2 different ones. let me know John hanson

Hello Not sure what you mean by dimensions but here goes 28'' Long 6 1/4" wide and 4" deep John Hanson 847 340 0727

If by chance your block is still good I have some new standard pistons for a 425 John Hanson

The is 150.00 plus shipping leave me a phone number or call me Just may be able to work something out on shipping I am going to Florida the first of feb. John Hanson

This is the Buick head I have. as I said the person I got this from wrote on it 1925 standard . He is not wrong to often. My inter change books only go back to 1930 so I do not know what years and models this will fit. John Hanson

I checked out the head today I don't know if it is any good to you the person I got wrote on it 1925 standard I for got to get the number off it i'll get in the morning if you thing you can use it. John Hanson

I have some motor mounts The book says 1372540 for 1965 66 400 engine. check the sides of your mounts and it should have a number on them. and a picture could help too. John Hanson

John If you didn't find it yet I should have some of them. Let me know and i'll check it out Sunday . I don't know if you need the 2 clips or the washer to hold the spring on. what ever I should have both. John Hanson

You may be right on the scam But I do about anything not to have to send pictures here. I can send pictures e mail or what ever . but when it come to this place I give up. I just don't even try any more. ( I must be doing something wrong) JohnHanson

I have a 6 cyl. Head I will check out the numbers wed. John Hanson