Bill Masters
Members-
Posts
26 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by Bill Masters
-
Again, thanks, everyone. I 'm working on a '34 Chevrolet tank that was coated on the inside many years ago, but whoever did it, did not do it well.
-
Thanks, guys. I am concerned about how well they stand up to the alcohol in the gas.
-
What is the best sealer to use inside a metal gas tank?
-
Tom, this may explain it. The nozzles are located inside the cylinder head casting and spray cool water on the seats from within.
-
Overhaul /Service Manual 1933 Master Sedan 4D
Bill Masters replied to mhotrodcars's topic in Chevrolet & GMC - General
Check here: https://www.faxonautoliterature.com/ -
Thank you, all for responding.
-
Does anyone know of a shop in the Raleigh, North Carolina area that can repair a three-inch crack in a cast iron engine block?
-
Almost done with 1938 Chevy master
Bill Masters replied to Mpgp1999's topic in Chevrolet & GMC - General
Mpgp1999, I do not know if the 1938 is the same, but on a 1934, the four-digit key code for the door lock and the ignition key is stamped on the door handle's shaft. Check the door handle to see if it has the code, and if it does, contact one of the lock smiths that advertises in the vintage auto magazines to see if they can cut a key for your lock. -
Impala, do you have the other half of the cover?
-
42319DB34, are you asking if the tire cover in my first post is for sale?
-
Can anyone identify this tire cover? I suspect the Chevrolet emblem is glued on. The Chevy guys say it is not Chevrolet
-
1932 Chevrolet Confederate clutch question??
Bill Masters replied to 34studepres's topic in Chevrolet & GMC - General
The reservoir will not remain full. Fill it and give it time to work. You should add oil only when the bearing is squeaking. -
1932 Chevrolet Confederate clutch question??
Bill Masters replied to 34studepres's topic in Chevrolet & GMC - General
Perhaps enough oil has not yet seeped into the bearing. If, over time, the reservoir's oil-level is going down, keep adding oil. -
1932 Chevrolet Confederate clutch question??
Bill Masters replied to 34studepres's topic in Chevrolet & GMC - General
34studepres, how are you lubricating the throwout bearing with it in the car? -
Mcdarrunt, I don't know of any assembly manuals for a 1934 Master, but if you have any questions, ask away. Also, there are many people over at the Chevy Chatter that enjoy helping. https://vccachat.org/
-
Bill, did you encounter a problem obtaining a good electrical ground for the bulbs with the coated reflectors?
-
Any reputable pot metal restorers out there?
Bill Masters replied to NC1968Riviera's topic in Chevrolet & GMC - General
Thank you, trimacar. -
Any reputable pot metal restorers out there?
Bill Masters replied to NC1968Riviera's topic in Chevrolet & GMC - General
I too would like to know. -
WTB: 1934 Chevrolet Master Radiator
Bill Masters replied to Bill Masters's topic in Chevrolet & GMC - General
Indianfour, thank you for the reply. My email is: wmasters50@charter.net. -
I am in need of a radiator or the top and bottom tanks, in very good condition, for a 1934 Master.
-
Can someone please tell me the part number for the housing cap on a DuBonnet (knee action) unit on a 1936 Pontiac?
-
Look under the front floor mat near the front of the passenger seat.
-
Thanks guys.
-
Did Pontiac build an El Comino style car in the 80's or 90's ?