|
|
|
Buick Reatta
|
|
Sounds like it's going to take more than Seafoam. You should pull the pan and check for shavings. Run a clean magnet through the oil. Also look for copper that won't get picked up by the magnet. If there's no shavings it will give you some bargaining
|
|
Buy/Sell
|
|
What do you want for the door panels and dash pad?
|
|
Buick - Post War
|
|
I think you're pretty smart, you knew where to look. And you're a good Buick guy too. Not everyone would post something like this. But, posting something like this is what makes this site very valuable. I have always been intrigued by why my fuel
|
|
Studebaker, Erskine & Rockne
|
|
Thanks to an AACA member Huptoy I got a tip that one was on Ebay this past week and bought it. Thanks again Huptoy. Stude8
|
|
V12 Lincolns
|
|
If you're sure about the connections and the wiring the trouble may be in the solenoid. The solenoid has 2 circuits, an engaging coil and a holding coil. A set of points that engage the holding coil are closed as the solenoid is activated. This actio
|
|
Buy/Sell
|
|
REgarding the kAISER, I have a nos horn ring for it, in case you or the ultimate buyer is interested. DAve 703 938-8954
|
|
Buy/Sell
|
|
Thanks for the tip Huptoy, I got on that item and won it. It is hard to judge the thread pitch but it looks pretty close to 16 TPI. Proves you can never tell what will come up on Ebay next. Stude8
|
|
Dodge & Dodge Brothers
|
|
If it's not too much trouble, I would really appreaciate a copy of the paint info also. I will pay for copying, postage, and a portion of the cost of the material. Please let me know. Thanks, Ken Lane, 1716 Oakview Dr., Roseville, CA 95661; or if
|
|
Ford and Mercury - 1932 to 1953
|
|
A friend of mine has a running 1946-1948 8 cylinder engine for sale. I have heard it run. It fires immediatly and runs well. PM me if interested.
|
|
Buick Riviera - Riviera Owners Association
|
|
After some further searching, I found a link that shows some pictures of the car I referenced in my previous thread. Buick built 61 of these cars for "offical" use.
|
|
Lincoln & Zephyr
|
|
Heads up. Posted on ebay: 1942 rear deck/trunk light handle with keys.
|
|
Buick Reatta
|
|
I wish I had the original headliner in my car. Anybody have one forsale, other than Jim Finn?
|
|
Buick Reatta
|
|
If steel chord is broken you will be riding on a time bomb. That bolt is huge. Tire will be safe at or below 15 MPH.
|
|
Buy/Sell
|
|
both are sold. thanks
|
|
Packard
|
|
dear flackmaster,my email is in the add. why dont you contact me & I will be glad to provide you with the info.thank you
|
|
Technical
|
|
The plastic pieces could be from the timing gear. They are coated in plastic to keep them quiet when the chain runs over them. As said, if you can move a piston 1/4 inch without moving anything else the engine is a time bomb.
|
|
Dodge & Dodge Brothers
|
|
Mark, just to make you think some more I have a spare'26 chassis if that will help this project get moving. An underslung speedster would be good!!
|
|
Buick Reatta
|
|
sweet to hear. It looks pretty cool in the manual
|
|
Buy/Sell
|
|
Condition, unknown. Block seems free of cracks. Accepting offers. Contact poobie1936@yahoo.com
|
|
Buy/Sell
|
|
Sorry for posting it wrong. As I drove past, I only saw the front, but it turns out that it is a 1&1/2 ton truck! The owner is asking $300, not the $250 I thought he had said earlier. Here's 2 pix: (more pix available upon request)
Pontiac & Oakland
|
|
Here's the problem: 1990 Bonne SE, Has good reverse, but no forward gears at all. The shifter arm on the tranny is moving properly when moving the shift lever thru the gears. For the last few days, when shifting into drive on a cold/cool engine, t
|
|
Pontiac & Oakland
|
|
This is an unrestored original
|
|
Buy/Sell
|
|
This is a matching numbers unrestored original car. Thanks ED
|
|
Buick - General
|
|
853: 15x 6 (5x5) 4th design: '67-'70. Center cap diameter 2'' Backspace is 3 3/8'' For a 71 and later you need 895
|
|
Buick - General
|
|
Derek Way back when I was driving a 55 regularly the tire sizes evolved from 7.60-15 to 8.45-15 to 8.55-15 to H78-15 to P225-75B15 (bias) or P225-75R15 (radial). Even though the width and diameter changed (they got lower and wider) the load range is
|
