Eric W Posted November 24, 2014 Share Posted November 24, 2014 Near as I can tell, the power windows from 1947 - 1953 were hydroelectric. Since my car isn't a convertible, I was thinking about maybe leaving the hydraulic pump for appearance, but not circulating the fluid inside the doors and cabin. I found this:nu-relics.com/hydraulic.html -bolt in conversion specific to these Buicks.Would be interested to hear if anyone else has done this, using these or a different product. Link to comment Share on other sites More sharing options...
1953mack Posted November 24, 2014 Share Posted November 24, 2014 https://nu-relics.com/hydraulic.htmlNo experience here with the conversion but it appears to be a well-de$$igned kit. Six or twelve-volt?Don't forget about the front seat hydraulic adjuster on your 76R Roadmaster two-door hardtop if you plan on deleting the entire hydraulic system. You might have to swap out the seat track mechanism to something that is similar to what's under your 41D four-door sedan front seat. Al MalachowskiBCA #8965"500 Miles West of Flint" Link to comment Share on other sites More sharing options...
Eric W Posted November 24, 2014 Author Share Posted November 24, 2014 Good catch, Al. Yes, I will be doing something with the seat. Could be a linear actuator that could be made to fit into the original seat adjuster. But as my 76R sits now, it does not have the correct front seat. It has a non-power-adjusted 2-door seat from something (the seat backs tip forwards on each side), but I don't know what. The original seat is gone. The electrohydraulic seat adjuster hardware was in the trunk. I saw one of these seats out of a Cadillac on ebay recently - they'd split it into about a thousand pieces, wanting dozens to hundreds of dollars for each piece. Might be nice if your car was missing one part, but to fight it out in a multitude of auctions to end up with a multi-thousand-dollar seat - I could probably dress up a more common seat to resemble, if not nearly replicate the original (if I can't find an original).It looks like the nu-relics window motors are all 12V. So another aspect of this is converting the whole car to 12V. That can also be done in a not-so-obvious way with a new-build one-wire alternator in a case that closely resembles the original generator case. I forget the name of the company that's building those, but it was in another thread on here.I'm not set on anything, but I looked into costs for restoring the hydraulics, and it's the same or more than the nu-relics window kits and 12V conversion combined. Then you still have the possibility of some sort of hydraulic fluid getting loose in the car and ruining paint, upholstery, etc. Link to comment Share on other sites More sharing options...
Guest Posted November 25, 2014 Share Posted November 25, 2014 In case your interested, I have a complete 1956 Roadmstr 6way power seat base assy that I was going to shorten for my 55 cent. I may consider selling it instead. PM me if you want to talk about itGood catch, Al. Yes, I will be doing something with the seat. Could be a linear actuator that could be made to fit into the original seat adjuster. But as my 76R sits now, it does not have the correct front seat. It has a non-power-adjusted 2-door seat from something (the seat backs tip forwards on each side), but I don't know what. The original seat is gone. The electrohydraulic seat adjuster hardware was in the trunk. I saw one of these seats out of a Cadillac on ebay recently - they'd split it into about a thousand pieces, wanting dozens to hundreds of dollars for each piece. Might be nice if your car was missing one part, but to fight it out in a multitude of auctions to end up with a multi-thousand-dollar seat - I could probably dress up a more common seat to resemble, if not nearly replicate the original (if I can't find an original).It looks like the nu-relics window motors are all 12V. So another aspect of this is converting the whole car to 12V. That can also be done in a not-so-obvious way with a new-build one-wire alternator in a case that closely resembles the original generator case. I forget the name of the company that's building those, but it was in another thread on here.I'm not set on anything, but I looked into costs for restoring the hydraulics, and it's the same or more than the nu-relics window kits and 12V conversion combined. Then you still have the possibility of some sort of hydraulic fluid getting loose in the car and ruining paint, upholstery, etc. Link to comment Share on other sites More sharing options...
PONTIAC1953 Posted November 25, 2014 Share Posted November 25, 2014 powermaster is the company that makes a 75 or 90 amp alternator look like an original delco generator.charles l. coker1953 pontiac tech advisortech advisor coordinatorpoci Link to comment Share on other sites More sharing options...
cbasta Posted September 23, 2019 Share Posted September 23, 2019 That link no longer works. Are there any other solutions for a 1951 Buick with hydro-electric power windows? Link to comment Share on other sites More sharing options...
Our Buicks Posted September 24, 2019 Share Posted September 24, 2019 (edited) On 9/23/2019 at 6:51 PM, cbasta said: That link no longer works. Are there any other solutions for a 1951 Buick with hydro-electric power windows? Here you go....Click on the menu, maybe this will help..... https://www.nu-relics.com/default.asp Mike Edited September 24, 2019 by Our Buicks (see edit history) 1 1 Link to comment Share on other sites More sharing options...
Beemon Posted September 25, 2019 Share Posted September 25, 2019 Did not know these existed! Thanks for the bump, will save a ton of headache converting over! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now