33Crazy Posted October 26, 2014 Share Posted October 26, 2014 (edited) Its been awhile since I posted but I am stilling plugging away at this restoration. I am restoring a 1933 Plymouth PD 4dr and need misc parts. 1. front back seat springs. 2. panel above windshield, covers wiper motor 3. tail light stand with/without license plate mount 4. drivers side window frame/molding 5. drivers side window channel used by the regulator 6. Radiator shell badge/emblem 7. rear lower seat spring 8. frame - has parallel left springs (at least from the x-member forward) Thanks, montanasman@gmail.com Edited November 21, 2016 by 33Crazy found some of the parts and need more (see edit history) Link to comment Share on other sites More sharing options...
Guest mikeburch Posted October 29, 2014 Share Posted October 29, 2014 I could have your tail light housing.I have many of that era, but unidentified. Do you have a photo of what you need ?Thank you,mikeburch Link to comment Share on other sites More sharing options...
Guest JPromo Posted November 2, 2014 Share Posted November 2, 2014 Do you have a picture of the door handles and cranks? I have assorted unidentified ones laying around. Link to comment Share on other sites More sharing options...
knobless Posted November 2, 2014 Share Posted November 2, 2014 may have some handles also have to check...... Link to comment Share on other sites More sharing options...
33Crazy Posted November 3, 2014 Author Share Posted November 3, 2014 (edited) Mike, Here are the pics...also I did find the radiator rods and a spare tire mount but would like a original spoke wheel.Thanks to all for respondingI am adding 2 more pics to show how the support plate looks as well as the stand with a license mount. Edited November 3, 2014 by 33Crazy (see edit history) Link to comment Share on other sites More sharing options...
33Crazy Posted November 3, 2014 Author Share Posted November 3, 2014 JPromo and Knobless, Here are the handle pics... Link to comment Share on other sites More sharing options...
knobless Posted November 5, 2014 Share Posted November 5, 2014 JPromo and Knobless, Here are the handle pics...[ATTACH=CONFIG]279052[/ATTACH] sorry the ones I have are different, still have wire wheels think I have 8-9 all good shape, some still have tires on them, (need replacing) also have many hub caps for same just need "skins"wheel will cost to ship, where are you located? I am in NH Link to comment Share on other sites More sharing options...
33Crazy Posted November 18, 2014 Author Share Posted November 18, 2014 I know I am in Florida but I am freezing my buns off. It is after noon and still only 38°. Since I ain't going outside (some of you are probably snow-bound) I thought I would ask a question. Has anyone put a B body rear under a 33 frame? I bought a spring kit from Chassis Engineering and plan on narrowing the B body rear that's 60.5 to 1.5" less than the stock rear that's 55.5" which will make it 54". Am I crazy or should I leave it at stock? Link to comment Share on other sites More sharing options...
Steve Braverman Posted December 8, 2014 Share Posted December 8, 2014 I have the radiator cap. $300 Link to comment Share on other sites More sharing options...
33Crazy Posted December 8, 2014 Author Share Posted December 8, 2014 has it been restored?Do you take PayPal? If so send me a valid email address.Is the radiator emblem below it for sale?Thanks Link to comment Share on other sites More sharing options...
Steve Braverman Posted December 8, 2014 Share Posted December 8, 2014 (edited) It has been replated in the past. It's been on a car for a while stored indoors, but the chrome is not perfect. It could probably be polished a little better, or it would be fine for a driver. The cap was on a 31 PA that my dad just bought, and I've replaced it with the correct cap. The emblem in the picture is on the car and is not for sale. My email is sdbraverman@gmail.com. PayPal is fine.I emailed you some more pictures. Edited December 8, 2014 by Steve Braverman (see edit history) Link to comment Share on other sites More sharing options...
knobless Posted December 27, 2014 Share Posted December 27, 2014 I am restoring a 1933 Plymouth PD 4dr and need misc parts.1. Spare orig tire and wheel2. NoLonger need...Flying lady radiator cap3. Radiator shell badge/emblem4. NoLonger need...3 ribbed interior window cranks5. 3 ribbed interior door handles6. NoLonger need...Radiator shell support rods7. NoLonger need...Left side oval dash panel8. Tail light housing with or without license mountThanks, gcclas@mail.comHi Chuck good chat today, the first picture, crank windshield handle is the shape I am looking for for all interior handles, the last 2 are whats in the car now..ThanksSteve Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now