Guest TakinitEZ Posted March 26, 2014 Share Posted March 26, 2014 I definitely have a little travel left and right in the front end. The steering wheel does not have much play but my front left wants to wander a bit. Suggestions for starting locations? I really don't want to do kingpins if I can avoid it. Link to comment Share on other sites More sharing options...
Mssr. Bwatoe Posted March 26, 2014 Share Posted March 26, 2014 Basics..Ck outer tie rods, at each wheel...ch drag link tie rods...have front end aligned..(set toe) Link to comment Share on other sites More sharing options...
Guest TakinitEZ Posted March 26, 2014 Share Posted March 26, 2014 Yep, looks like tie rod ends which is simple, but not cheap of course. $98/ea at Boos. And so it goes with classics... Link to comment Share on other sites More sharing options...
abelincoln Posted March 26, 2014 Share Posted March 26, 2014 Have you checked the wheel bearings? On the ground, grab top of tire and see if you can move it. Jack up and see how much play you have. Should be a little, but not much, and should spin freely without noise. Also, when jacked up move the steering wheel back and forth, shouldn't be any notches in steering gear. King pins sometimes wear as well. If you suspect the rod ends are bad, put vehicle on secure stands, watch from underneath while someone turns the wheel. Should not be discernible play. Does car squeak when you go over a bump? shock links may need replacing.Abe Link to comment Share on other sites More sharing options...
Guest TakinitEZ Posted March 26, 2014 Share Posted March 26, 2014 I will do that. It would not surprise me if wheel bearings needed at least to be repacked and adjusted. Easy enough to check them out. There is no squeek that I noted on my short drive. The tires are old as well, but in pretty good shape. Hoping they will round out fully when I get it back on the road a bit.Thanks! Link to comment Share on other sites More sharing options...
Mssr. Bwatoe Posted March 27, 2014 Share Posted March 27, 2014 Boos Herrill is nice, and has to make cash to finance the operation..but that is high...You can find em elsewhere1/3 price..mostly just generic ford parts..I have hard time understanding these prices..but if you dont have time too look, then pay triple list!! Link to comment Share on other sites More sharing options...
bclement Posted March 27, 2014 Share Posted March 27, 2014 I did bearings and seals all the way around and got everything from Alan Whelihan. Cheaper than Boos. He's got a parts and price list on the LZOC sources page. Link to comment Share on other sites More sharing options...
Guest TakinitEZ Posted March 31, 2014 Share Posted March 31, 2014 Thanks BC, Will give him a call. Link to comment Share on other sites More sharing options...
DSpringer Posted June 5, 2023 Share Posted June 5, 2023 Trying to resolve exessive slop in the steering of my '41 Zephyr. Installed new tie-rod ends and removed shims from the steering box, which seems tight now. I suspect worn kingpins but will be checking wheel bearings. I bought a set of kkingpins for a '41 Ford but it looks like they have a smaller diameter - 0.810" vs. the 0.933" that I measured after removing the lower retaining screw and cap. Merv Adkins used to offer them but he's been out of the game for a few years. Trying Whelihan and Boos-Herrel but they've been slow to respond. Seems like our old reliable parts sources are slowly fading away. Dave Link to comment Share on other sites More sharing options...
19tom40 Posted June 6, 2023 Share Posted June 6, 2023 To determine where the slop is in your steering, jack up one wheel, grab the front and back of the wheel and try to turn left to right. If you feel movement, get an assistant to either turn the wheel or crawl under the car to see where the movement is. To check the kingpins, grab the top and bottom of the wheel and try to move the top in and out. If you can then check the wheel bearings or see if the spindle is moving. A moving spindle means worn king pins. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now