Jump to content

Dean3326

Members
  • Posts

    34
  • Joined

  • Last visited

Everything posted by Dean3326

  1. Actually I have the Drawings right from Franklin,drawn in 1929 and they were followed to the T
  2. Everything needs to be installed all parts are tagged and bagged Price now $4900.00
  3. Body and running gear are still attached Price reduced $ 4900.00
  4. 1967 Corvette 427 390hp 4 spd number matching. Complete body off frame up restoration. 46798 mileage shown Marlboro Maroon exterior Dark Saddle Interior Tan top Side pipes Asking $95000.00 Dean 484-553-2042 George 610-554-5785
  5. Complete car. Restoration started customer lost interest vehicle is completely disassembled. Engine rebuilt by Kirk Arnold. All bright finish components were stripped and copper coated by Frank ford plating. SOLD
  6. Need a clutch release bearing and release collar that holds it. I understand an Auburn has similar parts.on the photos the items are # 10 and # 11. looking for any help.
  7. Getting ready to restore a 1938 Willys will be doing a 2 tone paint having trouble finding paint codes and formulas from 1942 Paint brochure the color choices are Bedford Grey ditzler IM -2373 QDE-1861 Mediator Blue ditzler IM-2609 QDE-2189 I have seen these colors also described as Regina Grey Willys grey Willy's rolls royce blue Could anyone help with the color formulas ?
  8. Getting ready to restore a 1938 Willys will be doing a 2 tone paint having trouble finding paint codes and formulas from 1942 Paint brochure the color choices are Bedford Grey ditzler IM -2373 QDE-1861 Mediator Blue ditzler IM-2609 QDE-2189 I have seen these colors also described as Regina Grey Willys grey Willy's rolls royce blue Could anyone help with the color formulas ?
  9. What is the proper answer do you or do you not lubricate the pilot bushing before installing the transmission ??
  10. I need a throw out bearing for a 1927 Gardner model 8B imperial sedan with a Borg & Beck clutch. 1926 and1927 specs show they are the same size 3.0 OD 1.75 Id .62 thickness as described in the instruction manual it was made of a special Graphite composition. I understand the Auburn is very similar to the Gardner. Any help is appreciated. Thank you Dean
  11. Looking for a clutch release bearing It is item #10 on attached photos.Clutch model#64 type 10 OL Borg & Beck
  12. Need a left rear axle for 1927 Gardner 8BS42915 lycoming engine 4HM12298 Shaft is 32.25 long 6 splines length 2.31 OD 1.44 end thread 1.0 V200 cast into housing Columbia stamped on axle shaft Also need the left inner bearing Bock # 03520 and seals I understand Auburn Cord similar parts Call with any information 484-553-2042 Dean
  13. Need a left rear axle for 1927 Gardner 8BS42915 lycoming engine 4HM12298 Shaft is 32.25 long 6 splines length 2.31 OD 1.44 end thread 1.0 V200 cast into housing Columbia stamped on axle shaft Also need the left inner bearing Bock # 03520 and seals I understand Auburn Cord similar parts Call with any information 484-553-2042 Dean
  14. Dean3326

    Gardner

    1927 Gardner Imperial sedan I need a left rear axle . 6 spline
  15. I need to get the gear shift apart I do not have a key Can anyone give me some advice ? Could the roll pin in the side be drilled out to separate the pieces ?
  16. Looking for a source for the webbing in the stabilizers. Anyone have a source ?
  17. Looking for an engine for a 1925 series 11A
  18. Looking for the floor brace between toe boards and floor boards. R811 drawing # 33507 Toe board Bar Need the door glass regulator lift channel for a front door Windshield rubber seal mounted into the frame on the vehicle
  19. I'm looking for a source for the Door side and upper channels. What is an acceptable replacement for these channels. Also looking for the Window regulator rubber compression lip for all 6 door channels. need 1 window channel with the lip to attach the compression lip. This vehicle has frame sag,I have the Franklin prints to attach the steel cable and turn buckle to remove the sag,has anyone had any luck with this setup? Thank you
  20. Hello. Restoring a 1969 Camaro Convertible I need the upper body dimensions. Does anyone have access to this information or know where I can get this information. I have tried the major collision dimension companies no luck. Hoping someone either has this info already or knows where I can turn to. Thank you
  21. Spark plugs ? 1926 franklin model 11A engine E103545 can anyone tell me the type of spark plug that should be in this vehicle. It now has autolite 3095 with a reducer going from the 1/2 pipe thread of the spark plug to 3/4 pipe screwed into the head. Problem being the od of that reducer barely screws into the head maybe on 3 threads. so something is obviously wrong. What is the original spark plug and what is its thread dimensions. Also a source for technical information what should compression be? Thank you
  22. Dean3326

    Franklin

    !926 Franklin looking for sources of any technical information I can get. also what should compression be on the vehicle?
  23. Spark plugs ? 1926 franklin model 11A engine E103545 can anyone tell me the type of spark plug that should be in this vehicle. It now has autolite 3095 with a reducer going from the 1/2 pipe thread of the spark plug to 3/4 pipe screwed into the head. Problem being the od of that reducer barely screws into the head maybe on 3 threads. so something is obviously wrong. What is the original spark plug and what is its thread dimensions. Thank you
×
×
  • Create New...