Maybe The End Of My Rope

[nick77]

I admit I am kinda new to this. I have done four cars from the sixty's which compared to this car were kid games. Four weeks ago I puchased a 1930 Chrysler 77, by all accounts a decent starter for its age. Looked good on the outside, motor running well,shifts smooth, and has most parts. But in order to drive I discovered I need two things,exhaust manifold and pressure plate.Two little things keeping me off the road, you would think I was trying to make gold from lead.I have talked to 350 people from 48 states and no help so far, yes many people refferred me to other sources but still no help. Many people suggest changing out motor and trans to something from the fiftys and solve my problem. Others say hang in there and hold out for original parts. I would like to stay original but my patience is wearing thin. Am I expecting to much to get my parts in four weeks or (still no answers) is this something I should get used to?

Still holding on Nick

[keiser31]

You may have to wait a bit more. Some folks are on vacations, some folks that restore those are not on this site. The car is rather rare (boy, am I gonna catch it for saying that) so try to hang in there. The parts for these are not on any store shelf. I have some feelers out there for your parts. Bear with us a while longer and don't do anything drastic like switching engines...yet.

[jscheib]

Is the manifold broken, or mising? Any chance of making a repair?

John

[nick77]

I removed the manifold and the cracks on the back side were very extensive. I went to old school welder who has fixed many in the past and he said unrepairable.

[MCHinson]

nick,

I don't know much about Chrysler products at all. Keiser would be the resident expert. If anybody can find your parts, he is your guy.

My father and brother were both welders and machinists. I am not either. From family experience, I would say that if no replacement parts can be found, the "unrepairable" can be repaired. It is just going to cost a lot more money than the welder thinks the job is worth. If it will keep the car on the road, it is worth more than the welder may realize.

Another option is Hershey. If the parts can be found, I would expect Hershey to be the place.

[nick77]

In Hershey is there a contact or do I need to visit?

[Neil G]

FYI, I sold that car a couple years ago to a guy in Cali. I didn't own it long but if you have any questions let me know.

[Dave Mellor NJ]

All you need to do at Hershey is show up with good shoes. You'll be surprised that there are still places like that and it's free except for parking.

[Bob Call]

Email these guys pictures of your clutch parts and see if they can help. Include some dimensions.

http://industrialbrakeclutch.com/

There has to be a source for a replacement clutch. I will take time to find it.

Reynolds & French have been repairing cracked castings for over 60 years primarily for the oil and gas industry. If there is no choice but repairing your manifold they are worth a try. Probably not cheap.

http://www.r-f.com/crack_repair.asp

Might ask them about the broken clutch pressure plate also since it is cast.

[hchris]

Whilst not an expert on the 77 I can tell you that other 6 cylinder Chrysler/Desoto and possibly Dodge models of that era share similar if not the same engine parts; so dont just limit your search to the 77 and look at younger cars up to 1934 at least.

[B campbell]

I read about a guy in the hot rod mag that was a tempting a land speed record with a 32 Chrysler and he was re making stuff for the top speed I'm sure he took off all the good stuff to make go fast parts.the name of his shop is EDGY speed shop his name is earl edgerton I don't know if this will help but you seem to be at the end of your rope good luck on the search

[KenHupp20]

You may want to look for a welder with experience with Muggy weld.
I have never used it myself.
Muggy Weld LLC Specialty Welding Alloys and Electrodes

[MCHinson]

nick,

Regarding Hershey, check out the "AACA National Eastern Division Meet - Hershey" discussion.

[Steve_Mack_CT]

Nick, good luck with it. Internet is very very helpful and has changed the hobby BUT there are still a lot of "old timers" (and not so old) who want nothing to do with it. If you haven't already I would join the Chrysler club - it may take a little time but that may be another route, especially if they publish a roster with member's cars, or have a good vendor directory. That will help you in the future also.

The only other thought is try another welder on the manifold, if it is already broken you really have nothing to lose, even if it is a temporary fix.

Good luck with it -

[starfireelvis]

I have a good friend name Jim Russell who takes his 1930 Chrysler 77 to Hershey; I am assuming he will do so once again this year. I can try to find his contact info if you wish, send me a PM if you want me to do so, with your contact info as well...Mike

[Restorer32]

Welcome to the world of old car restoration.

[Dandy Dave]

Gees, I know of a straight eight Desoto, about the same vintage, not far from here in a scrap yard that still has the manifold on it. If only it were an 8, instead of a 6. Dandy Dave!

[Paul Dobbin]

Ah, the joy of antique cars! One if the things that make the completed drivable old car so attractive to most of us is the fact that to get it to that stage the owner had to go through what you are experiencing. If it was easy to find parts and repair these old beauties, there would be a lot more of them driving around.
The hunt for the parts is part of the enjoyment of ownership. This is where people you know can make a big difference, as illustrated by the offers of helpful advice on this forum. The AACA is a good source and the Chrysler Club
would be more specific. Don't forget you local antique car club.
I had a friend put me onto a welder that successfully re-constructed a manifold
for me for my 35 Buick. (It's worked fine for more than 12 years now)
But, you are right it doesn't happen quickly, you'll have to get use to that.
You'll meet people who can help you and even some you can help, enjoy the process.

[alsancle]

That exhaust manifold can be repaired by a good stitch welder. Of course, those guys are practically non existent. You should be able to replace the entire clutch/pressure plate assembly with a modern replacement. I'm running a ford truck setup on my Stutz. Unfortunately, you need someone to have already figured out the best swap or do it yourself.

[keiser31]

That exhaust manifold can be repaired by a good stitch welder. Of course, those guys are practically non existent. You should be able to replace the entire clutch/pressure plate assembly with a modern replacement. I'm running a ford truck setup on my Stutz. Unfortunately, you need someone to have already figured out the best swap or do it yourself.

I agree with this. Give us the size of the clutch (diameter and overall thickness)and we may be able to match it up.

[poci1957]

You should be able to replace the entire clutch/pressure plate assembly with a modern replacement.

Alsancle makes a good point here. If you go to the parts store and tell them you have a 1930 Chrysler they will immediately zone out and say they have nothing for you. But if you plop your part on the counter and ask for "one of these" you may hit on a common modern replacement. This works especially with bearings and seals too. (NOTE select a parts store with some evidence of traditional gear-headedness going on. An Auto Zone with a 20 year old may not be ready for anything not on the computer)

It IS harder than dealing with 1960s cars and that is why the guy working on something like this can earn the satisfaction (?) of being able to overcome adversity that makes his buddies with 1969 Chevys look soft and weak by comparison. Good luck, Todd C

[Friartuck]

Like KenHupp20, I recommend going the repair route with MuggyWeld.com cast iron welding rods. You need both the 77 and 72 type rods: one for dirty cast iron (and an exhaust manifold qualifies as dirty) and the other to top over the first. I've used them successfully. Get a used manifold (perhaps a marine manifold from a junk yard) to practice on, (or whoever is doing the actual welding to practice on). Read instructions carefully, you have to use a back stich method of applying the rod. They're vidoes go a long way to show the results.

Chris Wantuck

[60FlatTop]

If I wanted to drive that car I would have a flanged steel exhaust "header" fabricated while I looked for the proper replacement.

The need of a pressure plate seems odd. A call to Rochester Clutch & Brake at 585-232-3717; should have that resolved in short time.

If those don't sound like good ideas let me know how much you will sell that unrepairable car for. It shouldn't be worth much but I have a little.
Bernie

[keiser31]

Gees, I know of a straight eight Desoto, about the same vintage, not far from here in a scrap yard that still has the manifold on it. If only it were an 8, instead of a 6. Dandy Dave!

And you left the yard WITHOUT that manifold? How much of that chassis is remaining? Are there other parts that could be gotten from it. Got photos???

[1912Staver]

Hi Nick, exhaust manifolds are one of those parts that most old cars seem to need eventually. Some are available reproduction, {sometimes offered by a one make club spares service} but many are not. There are three options; wait for a usable original, replace with a fabricated manifold {tube and plate welded replacement} and finally commission a new casting. The last option is the best but of course the most expensive. There are a couple of places that advertise in Hemmings etc. You might be able to find a retired pattern maker locally who can produce a pattern at a better than the going rate price, but the casting itself will need to be done by a commercial foundry. If you go this route it usually pays to get several castings made so you can sell them to others in your predicament and so recover at least some of the cost of the pattern. You would be amazed at how many custom castings have been made for the restoration of pre-war cars over the years. If it was made originally , it can be re made today. The only obstacle is the cost. P.S. yes in my opinion you are asking too much, people often look for years for certain replacement parts. Think of every part on your Chrysler to be the equivalent of 1963 max wedge parts and you will begin to get the picture.
All the best, Greg in Canada